How to correctly install a Sensor Adapter

How to correctly install a Sensor Adapter
BioscienZ optimiert die Fermentationsforschung mit Reporter
Intelligente Überlaufüberwachung im Kanalisationsnetz von Aquafin
A-Renting: Kühlcontainer-Vermietung mit zuverlässiger Temperaturüberwachung dank Reporter
Effiziente Energie-, Wasser- und Gasüberwachung: Nachhaltigkeit & Kosteneinsparungen für Ihre Fabrik
Professioneller ferngesteuerter Regenmesser mit digitaler Messung
Baummonitoring während der Wasserhaltung: Schutz für gesunde Bäume
Luftfeuchtigkeitsüberwachung für Papier- und Kartonlager
CO₂-Überwachung in der Nutztierhaltung: längst überfällig
Innovative Überwachung von Böschungen entlang der A10 mit Reporter
Eine Wetterstation mit Wasserstandssensor für eine Marina oder einen Hafen
Colruyt Group setzt Reporter zur Messung der Bodenfeuchte auf dem Bio-Bauernhof Het Zilverleen ein
Salzgehalt im Grundwasser erkennen: Überwachung der Salinität bei Grundwasserabsenkung
Royal Latem Golf Club nutzt Reporter zur Überwachung des Wasserverbrauchs
Verbinden Sie Ihren Wasser-Durchflusssensor mit der Cloud
Sensoradapter: Was sind sie und wie funktionieren sie?
Rode Rozen & Tortilla's nutzt Reporter zur Überwachung der Gefrierschränke
Artes Woudenberg nutzt Reporter zur Windüberwachung bei der Restaurierung des Brüsseler Justizpalasts
Intelligente Häfen mit IoT: Die Zukunft des Transports
Wetterdaten zur Vermeidung ungerechtfertigter Liegegeldforderungen
Pluym - Van Loon nutzt Reporter zur Grundwassermessung in der Projektentwicklung
Baustellenüberwachung – Sicherheit & Effizienz
Effektive Überwachung industrieller Geruchsbelästigung
Warum Temperaturkontrolle ohne Fernüberwachung unvollständig ist
Taste Restaurantgroup nutzt Reporter zur Gefrierüberwachung
Cemminerals nutzt Reporter zur Temperaturmessung des Kanalwassers
Rombaut Plant setzt auf Reporter für die Frostüberwachung in der Containerkultivierung
Vandijk Technics setzt Reporter zur Temperaturüberwachung in Kühlzellen ein
Kombinierte Messung von relativer Luftfeuchtigkeit und Blattnässe
Innovatives Baummonitoring: Ecomatik-Dendrometer & Reporter
De Bossen misst Bodenfeuchtigkeit für eine erfolgreiche Stangenbohnenernte
TM Edison setzt Reporter beim Bau der Energieinsel ein
Was ist der Unterschied zwischen direkten und indirekten Energiezählern?
Wetterüberwachung: Windmessung auf einem Festivalgelände
Den richtigen Durchflussmesser für Ihr Wasserprojekt wählen
Wie misst man den Taupunkt und die Feuchtkugeltemperatur?
Präzisionstest für den Sensirion SHT35 Feuchtigkeitssensor
Wetterüberwachung für Wohnwagen und Ferienhäuser
Die Auswirkungen von Wind auf die Messung von Feinstaub
Watermark-Sensor mit der Cloud verbinden
Watermark vs. SMT100: Volumetrischer Wassergehalt oder Bodenwasseranspannung?
Intelligente geotechnische Datenerfassung und Analyse
6 Tipps für die optimale Nutzung Ihrer Kühlzelle
Temperaturaufzeichnung für HACCP
Die 7 HACCP-Grundsätze einfach umsetzen
6 Listen, um schnell mit HACCP zu starten
Überwachung der Bodenfeuchte im Pflanzenanbau
Grüne Wandüberwachung: So halten Sie Ihre vertikale Begrünung gesund
Wie wird der Reporter mit Strom versorgt?
Sturm & Gerüst: Wetterstationen für mehr Baustellensicherheit
Füllstandsmessung in einem Behälter oder Brunnen

Without Sensor Adapters, your measuring journey would become a strenuous one. Adapters require correct installation to stay in their best shape, guaranteeing a long lifetime of the hardware.

Signal quality

As Sensor Adapters were created to interpret sensors, they like to stay close to them. Connect your adapter as close to your sensor as possible.

Signal integrity is essential for accurate sensor readings. Maintaining a 5 cm buffer zone around the adapter helps minimise disruption from electrical wires, especially those carrying high currents.

Shade & Temperature

Maximise the lifetime of your Sensor Adapter by avoiding exposure to direct sunlight and extreme temperatures which can degrade the adapter over time. Please follow these guidelines:

  • Temperature range: The adapter is optimised for temperatures between -10°C and +40°C. Avoid placing it near heat sources or in areas subject to extreme cold to prevent damage.
  • UV protection: Prolonged exposure to sunlight can damage the material, especially the rubber rings that seal the adapter. Place the adapter in shaded areas whenever possible to protect against UV damage.
Three Sensor Adapters

Clean & Dry installation

Moisture and dirt don't mix with hardware. When moisture, mud, or dirt gets into your Sensor Adapter or M12 connectors, it will cause a bad connection and even break your connecting ports.

With the correct installation, your Sensor Adapter is IP65 after being fully closed. This means that it's highly resistant to dust and can withstand low-pressure water jets from all directions.

Important to note is that as long as your adapter is open, or not installed correctly, the IP65 rating is voided.

The following two measures help avoid moisture and dirt from entering your hardware:

  • Horizontal cable orientation: Ensure incoming and outgoing wires are positioned either horizontally or directed downward. This positioning prevents water from entering the adapter through the cables.
  • Long cables: Avoid using multiple extension cords when you can opt for longer cables instead (one 20 m cable instead of four 5 m ones). This helps you decrease possible points of failure.

Close with clean insides

Before closing, inspect both halves of the adapter for any dirt, dust, or moisture. If trapped inside, these particles can cause a bad connection as well as corrosion and abrasion, ultimately damaging the adapter. Use a clean, dry cloth if necessary.

  • Dirt in the thread of the adapter abrades the texture of the thread, causes damage, and makes the adapter vulnerable to water infiltration.
  • Keep the rubber rings clean at all times, or you will weaken the seal. Dirt causes damage and will void the watertightness of the device.
  • Always ensure the adapter is fully and correctly closed after connecting a sensor. This prevents water infiltration and protects internal components.

Dust caps

All unused M12 connectors should be protected with an M12 dust cap as shown in the image below. Every Reporter comes with five dust caps.

Should you lose a dust cap, you can contact us for a replacement.

Reporter dust caps

Where & How?

Positioning your adapter properly can extend its lifetime and prevent potential damage, which is why we recommend the following guidelines:

  • Mounting height: Place the adapter at least 50 cm above the ground to avoid exposure to mud, water, or other ground-based contaminants.
  • Horizontal placement: For outdoor installations, mount the adapter horizontally. This reduces the risk of water entering through any cables or connections.
  • Secure mounting base: Attach the adapter to a stable surface like a wall or pole to prevent accidental contact with the ground.
  • Keep off the ground: Never place the adapter directly on the ground, as it risks blunt force damage (e.g., from being stepped on or driven over) or exposure to contaminants.

Please remember: as long as your adapter is open, or not installed correctly, the IP65 rating is voided.

Electrical cabinets

Are you using an electrical cabinet for your project? Read all the guidelines regarding this specific kind of installation in our blog below:

Any questions?

If you still have any questions after reading this blog, don't hesitate to reach out to us!

Zurück zum Blog

Haben Sie Fragen?

Rufen Sie uns an unter +32474097705 Oder nutzen Sie das Kontaktformular

1 von 4
  • Demo laptop

    Live-Online-Demo

    Registrieren Sie sich für ein kostenloses Konto im Crodeon Dashboard und sehen Sie sich eine echte Live-Demo in Aktion an.

    Demo ansehen 
  • person

    Sprechen Sie mit dem Vertrieb

    Vereinbaren Sie einen Termin mit Jonathan, unserem Vertriebsleiter, um mehr über diese Lösung zu erfahren.

    Vereinbaren Sie einen Anruf 
  • phone email

    Kontaktieren Sie uns

    Für Partnerschaften, Vertrieb oder andere Anfragen – zögern Sie nicht, uns zu kontaktieren!

    Kontaktieren Sie uns